Version 0.5-beta with new USB VID_0x1d50/PID_0x60a7 using OpenMoko Hy…

…draFW

09-hydrabus.rules

@@ -3,5 +3,5 @@
 # To install, type this command in a terminal:
 #   sudo cp 09-hydrabus.rules /etc/udev/rules.d/09-hydrabus.rules
 #
-SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="5740", ENV{ID_MM_DEVICE_IGNORE}="1"
-SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="5740", MODE="0664", GROUP="plugdev"
+SUBSYSTEMS=="usb", ATTRS{idVendor}=="1d50", ATTRS{idProduct}=="60a7", ENV{ID_MM_DEVICE_IGNORE}="1"
+SUBSYSTEMS=="usb", ATTRS{idVendor}=="1d50", ATTRS{idProduct}=="60a7", MODE="0664", GROUP="plugdev"

CHANGELOG.md

@@ -1,6 +1,38 @@
 # CHANGELOG of 'hydrafw'
 ----------------------
 
+#### 11.02.2015 - [HydraFW v0.5 Beta](https://github.com/bvernoux/hydrafw/releases/tag/v0.5-beta)
+* New USB VID_0x1d50/PID_0x60a7 using OpenMoko HydraFW, update with new drivers
+  * Windows see driver_usb_cdc/hydrabus_usb_cdc.inf
+  * Linux see 09-hydrabus.rules
+* Added USB DFU boot by pressing UBTN at PowerOn/RESET for easier future update of the firmware (does not requires any wire).
+* Added Log command (thanks to biot):
+  * Log all commands/answer in the Terminal to HydraBus SD card file: `logging` `on` `off` `sd`
+* Added command `debug` `test-rx` (debug rx) in order to test USB CDC reception performance.
+* Added PWM command:
+  * Configurable PWM frequency between 1Hz to 42MHz and duty cycle from 0 to 100%: `pwm`, `frequency`, `duty-cycle`
+  * Give feedback of real PWM frequency & duty cycle after configuration.
+* Added DAC command:
+  * Configurable DAC1(PA4 used by ULED) or DAC2(PA5) with following modes:
+    * `raw` (0 to 4095), `volt` (0 to 3.3), also returns feedback of raw/volt DAC value after configuration.
+    * `triangle` (5Hz / 3.3V Amplitude), `noise` (0 to 3.3V Amplitude)
+    * `dac exit` disable DAC1/2 & Timer6/7 and reinit GPIO for PA4 & PA5
+* UART:
+  * UART returns real baud rate+% error after configuration.
+  * Check and correct min/max value for UART baudrate.
+* I2C added `scan` (thanks to biot).
+* SPI:
+  * Fixed `cs` `on` / `off` bug with Infinite Loop.
+  * Fixed SPI mode `slave`.
+  * Fixed configuration for `phase` & `polarity` (was always set to 0).
+* HydraNFC: 
+  * Fixed HydraNFC detection/init/cleanup and autonomous sniffer mode started with K4.
+  * Fixed some potential problems/crash with scan/continuous.
+* Add full help for commands.
+* Lot of cleanup and fixes in code.
+
+---
+
 #### 19.12.2014 - [HydraFW v0.4 Beta](https://github.com/bvernoux/hydrafw/releases/tag/v0.4-beta)
 * Major improvement/refactoring towards terminal/syntax using tokenline (instead of microrl) thanks to Bert Vermeulen (biot) for that amazing piece of software and all the work on this project.
 * New commands added:

common/usb1cfg.c

@@ -17,6 +17,9 @@ limitations under the License.
 #include "ch.h"
 #include "hal.h"
 
+#define VENDOR_ID		0x1d50
+#define PRODUCT_ID	0x60a7
+
 /*
  * Endpoints to be used for USBD1.
  */
@@ -34,8 +37,8 @@ static const uint8_t vcom_device_descriptor_data[18] = {
 		0x00,          /* bDeviceSubClass.                 */
 		0x00,          /* bDeviceProtocol.                 */
 		0x40,          /* bMaxPacketSize.                  */
-		0x0483,        /* idVendor (ST).                   */
-		0x5740,        /* idProduct.                       */
+		VENDOR_ID,     /* idVendor.                        */
+		PRODUCT_ID,    /* idProduct.                       */
 		0x0200,        /* bcdDevice.                       */
 		1,             /* iManufacturer.                   */
 		2,             /* iProduct.                        */
@@ -155,11 +158,10 @@ static const uint8_t vcom_string0[] = {
  * Vendor string.
  */
 static const uint8_t vcom_string1[] = {
-	USB_DESC_BYTE(38),                    /* bLength.                         */
+	USB_DESC_BYTE(30),                    /* bLength.                         */
 	USB_DESC_BYTE(USB_DESCRIPTOR_STRING), /* bDescriptorType.                 */
-	'S', 0, 'T', 0, 'M', 0, 'i', 0, 'c', 0, 'r', 0, 'o', 0, 'e', 0,
-	'l', 0, 'e', 0, 'c', 0, 't', 0, 'r', 0, 'o', 0, 'n', 0, 'i', 0,
-	'c', 0, 's', 0
+	'O', 0, 'p', 0, 'e', 0, 'n', 0, 'm', 0, 'o', 0, 'k', 0, 'o', 0,
+	',', 0, ' ', 0, 'I', 0, 'n', 0, 'c', 0, '.', 0
 };
 
 /*

common/usb2cfg.c

@@ -17,6 +17,9 @@ limitations under the License.
 #include "ch.h"
 #include "hal.h"
 
+#define VENDOR_ID		0x1d50
+#define PRODUCT_ID	0x60a7
+
 /*
  * Endpoints to be used for USBD2.
  */
@@ -34,8 +37,8 @@ static const uint8_t vcom_device_descriptor_data[18] = {
 		0x00,          /* bDeviceSubClass.                 */
 		0x00,          /* bDeviceProtocol.                 */
 		0x40,          /* bMaxPacketSize.                  */
-		0x0483,        /* idVendor (ST).                   */
-		0x5740,        /* idProduct.                       */
+		VENDOR_ID,     /* idVendor.                        */
+		PRODUCT_ID,    /* idProduct.                       */
 		0x0200,        /* bcdDevice.                       */
 		1,             /* iManufacturer.                   */
 		2,             /* iProduct.                        */
@@ -152,11 +155,10 @@ static const uint8_t vcom_string0[] = {
  * Vendor string.
  */
 static const uint8_t vcom_string1[] = {
-	USB_DESC_BYTE(38),                    /* bLength.         */
-	USB_DESC_BYTE(USB_DESCRIPTOR_STRING), /* bDescriptorType. */
-	'S', 0, 'T', 0, 'M', 0, 'i', 0, 'c', 0, 'r', 0, 'o', 0, 'e', 0,
-	'l', 0, 'e', 0, 'c', 0, 't', 0, 'r', 0, 'o', 0, 'n', 0, 'i', 0,
-	'c', 0, 's', 0
+	USB_DESC_BYTE(30),                    /* bLength.                         */
+	USB_DESC_BYTE(USB_DESCRIPTOR_STRING), /* bDescriptorType.                 */
+	'O', 0, 'p', 0, 'e', 0, 'n', 0, 'm', 0, 'o', 0, 'k', 0, 'o', 0,
+	',', 0, ' ', 0, 'I', 0, 'n', 0, 'c', 0, '.', 0
 };
 
 /*

driver_usb_cdc/hydrabus_usb_cdc.inf

@@ -80,10 +80,10 @@ ServiceBinary=%12%\%DRIVERFILENAME%.sys
 [SourceDisksFiles]
 [SourceDisksNames]
 [DeviceList]
-%DESCRIPTION%=DriverInstall, USB\VID_0483&PID_5740
+%DESCRIPTION%=DriverInstall, USB\VID_1D50&PID_60A7
 
 [DeviceList.NTamd64]
-%DESCRIPTION%=DriverInstall, USB\VID_0483&PID_5740
+%DESCRIPTION%=DriverInstall, USB\VID_1D50&PID_60A7
 
 
 ;------------------------------------------------------------------------------