forked from raburton/rboot
-
Notifications
You must be signed in to change notification settings - Fork 0
/
rboot.h
159 lines (129 loc) · 5.6 KB
/
rboot.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
#ifndef __RBOOT_H__
#define __RBOOT_H__
//////////////////////////////////////////////////
// rBoot open source boot loader for ESP8266.
// Copyright 2015 Richard A Burton
// See license.txt for license terms.
//////////////////////////////////////////////////
#ifdef __cplusplus
extern "C" {
#endif
#include <c_types.h> // uint* types
#ifdef RBOOT_INTEGRATION
#include <rboot-integration.h>
#endif
// uncomment to use only c code
// if you aren't using gcc you may need to do this
//#define BOOT_NO_ASM
// uncomment to have a checksum on the boot config
//#define BOOT_CONFIG_CHKSUM
// uncomment to enable big flash support (>1MB)
//#define BOOT_BIG_FLASH
// uncomment to enable 2 way communication between
// rBoot and the user app via the esp rtc data area
//#define BOOT_RTC_ENABLED
// uncomment to enable GPIO booting of specific rom
// (specified in rBoot config block)
// cannot be used at same time as BOOT_GPIO_SKIP_ENABLED
//#define BOOT_GPIO_ENABLED
// uncomment to enable GPIO rom skip mode, trigger
// GPIO at boot time to skip to next rom
// cannot be used at same time as BOOT_GPIO_ENABLED
//#define BOOT_GPIO_SKIP_ENABLED
// set the GPIO pin used by GPIO modes above (will default
// to 16 if not manually set), only applicable when
// BOOT_GPIO_ENABLED or BOOT_GPIO_SKIP_ENABLED is enabled
//#define BOOT_GPIO_NUM 16
// uncomment to include .irom0.text section in the checksum
// roms must be built with esptool2 using -iromchksum option
//#define BOOT_IROM_CHKSUM
// uncomment to add a boot delay, allows you time to connect
// a terminal before rBoot starts to run and output messages
// value is in microseconds
//#define BOOT_DELAY_MICROS 2000000
// define your own default custom rBoot config, used on
// first boot and in case of corruption, standard fields
// (magic, version and chksum (if applicable) are included
// for you automatically), see example at end of this file
// and customise as required
//#define BOOT_CUSTOM_DEFAULT_CONFIG
// max number of roms in the config (defaults to 4), higher
// values will use more ram at run time
//#define MAX_ROMS 4
// you should not need to modify anything below this line,
// except default_config() right at the bottom of the file
#define CHKSUM_INIT 0xef
#define SECTOR_SIZE 0x1000
#define BOOT_CONFIG_SECTOR 1
#define BOOT_CONFIG_MAGIC 0xe1
#define BOOT_CONFIG_VERSION 0x01
#define MODE_STANDARD 0x00
#define MODE_GPIO_ROM 0x01
#define MODE_TEMP_ROM 0x02
#define MODE_GPIO_ERASES_SDKCONFIG 0x04
#define MODE_GPIO_SKIP 0x08
#define RBOOT_RTC_MAGIC 0x2334ae68
#define RBOOT_RTC_READ 1
#define RBOOT_RTC_WRITE 0
#define RBOOT_RTC_ADDR 64
// defaults for unset user options
#ifndef BOOT_GPIO_NUM
#define BOOT_GPIO_NUM 16
#endif
#ifndef MAX_ROMS
#define MAX_ROMS 4
#endif
/** @brief Structure containing rBoot configuration
* @note ROM addresses must be multiples of 0x1000 (flash sector aligned).
* Without BOOT_BIG_FLASH only the first 8Mbit (1MB) of the chip will
* be memory mapped so ROM slots containing .irom0.text sections must
* remain below 0x100000. Slots beyond this will only be accessible via
* spi read calls, so use these for stored resources, not code. With
* BOOT_BIG_FLASH the flash will be mapped in chunks of 8MBit (1MB), so
* ROMs can be anywhere, but must not straddle two 8MBit (1MB) blocks.
* @ingroup rboot
*/
typedef struct {
uint8 magic; ///< Our magic, identifies rBoot configuration - should be BOOT_CONFIG_MAGIC
uint8 version; ///< Version of configuration structure - should be BOOT_CONFIG_VERSION
uint8 mode; ///< Boot loader mode (MODE_STANDARD | MODE_GPIO_ROM | MODE_GPIO_SKIP)
uint8 current_rom; ///< Currently selected ROM (will be used for next standard boot)
uint8 gpio_rom; ///< ROM to use for GPIO boot (hardware switch) with mode set to MODE_GPIO_ROM
uint8 count; ///< Quantity of ROMs available to boot
uint8 unused[2]; ///< Padding (not used)
uint32 roms[MAX_ROMS]; ///< Flash addresses of each ROM
#ifdef BOOT_CONFIG_CHKSUM
uint8 chksum; ///< Checksum of this configuration structure (if BOOT_CONFIG_CHKSUM defined)
#endif
} rboot_config;
#ifdef BOOT_RTC_ENABLED
/** @brief Structure containing rBoot status/control data
* @note This structure is used to, optionally, communicate between rBoot and
* the user app. It is stored in the ESP RTC data area.
* @ingroup rboot
*/
typedef struct {
uint32 magic; ///< Magic, identifies rBoot RTC data - should be RBOOT_RTC_MAGIC
uint8 next_mode; ///< The next boot mode, defaults to MODE_STANDARD - can be set to MODE_TEMP_ROM
uint8 last_mode; ///< The last (this) boot mode - can be MODE_STANDARD, MODE_GPIO_ROM or MODE_TEMP_ROM
uint8 last_rom; ///< The last (this) boot rom number
uint8 temp_rom; ///< The next boot rom number when next_mode set to MODE_TEMP_ROM
uint8 chksum; ///< Checksum of this structure this will be updated for you passed to the API
} rboot_rtc_data;
#endif
// override function to create default config, must be placed after type
// and constant defines as it uses some of them, flashsize is the used size
// (may be smaller than actual flash size if big flash mode is not enabled,
// or just plain wrong if the device has not been programmed correctly!)
#ifdef BOOT_CUSTOM_DEFAULT_CONFIG
static uint8 default_config(rboot_config *romconf, uint32 flashsize) {
romconf->count = 2;
romconf->roms[0] = SECTOR_SIZE * (BOOT_CONFIG_SECTOR + 1);
romconf->roms[1] = (flashsize / 2) + (SECTOR_SIZE * (BOOT_CONFIG_SECTOR + 1));
}
#endif
#ifdef __cplusplus
}
#endif
#endif